Bonjour, avez vous déjà changé ce type de pièce ou avez-vous une solution pour le tester.
J'ai celui-ci a changer sur mon véhicule, mais j'aimerais essayer de le réparer ou de le tester moi-même avant de le changer.
C'est sur mon Audi de 2008 8PA.
-------------------------------------------------------------------------------
Address 01: Engine (CBA) Labels: 03L-906-022-CBA.clb
Part No SW: 03L 906 022 BQ HW: 03L 906 022 BQ
Component: R4 2,0L EDC G000SG 3066
Revision: 13H01--- Serial number: AUX7Z0H6FN90US
Coding: 0000072
Shop #: WSC 83712 666 534886
VCID: 75ED62D74CC136AB205
2 Faults Found:
009253 - Exhaust Gas Recirculation Cooling Valve Control
P2425 - 000 - Open Circuit - MIL ON
Freeze Frame:
Fault Status: 11100000
Fault Priority: 2
Fault Frequency: 61
Mileage: 143699 km
Time Indication: 0
Date: 2022.01.06
Time: 01:36:38
Freeze Frame:
RPM: 782 /min
Speed: 0.0 km/h
Temperature: 44.1°C
Absolute Pres.: 969.0 mbar
(no units): 30.6
(no units): 1.31
Temperature: 84.6°C
008213 - Intake Manifold Flap Position Sensor (Bank 1)
P2015 - 000 - Implausible Signal - MIL ON
Freeze Frame:
Fault Status: 11100000
Fault Priority: 2
Fault Frequency: 1
Mileage: 143699 km
Time Indication: 0
Date: 2022.01.06
Time: 01:36:38
Freeze Frame:
RPM: 782 /min
Speed: 0.0 km/h
Load: 0.0 %
Lambda: 11.8 %
Lambda: 0.0 %
Voltage: 0.228 V
Bin. Bits: 00000000
Readiness: 1 2 0 0 1
-------------------------------------------------------------------------------
009253 - Exhaust Gas Recirculation Cooling Valve Control
P2425 - 000 - Open Circuit
Special Notes
- Check TSB 24-17-04 or 2045138 NAR) North American Region vehicles only.
- 2006 - 2008 BPY and 2008 - 2016 CCTA and CBFA engines.
- Improved intake manifold design.
Les liens ne sont visibles que pour les membres confirmés.NHTSA- In some Cases the Issue can only be resolved by Replacing the whole Intake Manifold.
- The Intake Manifold Flap Motor (V157) and Manifold Runner Position Sensor (G336) may be Part of the same Unit.
- When found in a VW Golf/Jetta (1K): 1.9l PD-TDI (BRM), check Engine Control Module (ECM) Software Version:
- 03G-906-016-AB @ 7328 or 7550 as well as 03G-906-016-AC @ 7280 or 7551 do have a Software Error which requires a special Adaptation for the Intake Manifold Flap Motor (V157) which at this Point can only be performed with the Factory Tool.
- This page describes a Basic Settings for some 2.0T gasoline engines:
Les liens ne sont visibles que pour les membres confirmés.- When found in North America Audi vehicles check Technical Service Bulletin number: 2044003
- This TSB addresses possible issues with the N316 - Intake Manifold Flap Valve
Les liens ne sont visibles que pour les membres confirmés.NHTSA
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?