Niko VR6
Membres
- Inscrit
- 25/2/21
- messages
- 163
- Localisation
- Metz, Grand Est,France
- Marque
- VW
- Modèle
- Touran
- Date
- 23/9/03
- Cylindrée
- 2
- Km
- 280000
- Type
- Diesel
- Code moteur
- AZV
- VIN
- WVGZZZ1TZ4W048222
- VCDS
- VCDS
Special Notes
If the remotes will not operate but are confirming while matching during the Adaptation process check the following possible causes:
- Verify the module is not new and still in Factory Mode.
- Check the ignition S-contact switching and driver door latch measuring block switching because remotes will not lock the doors if either are faulty/implausible.
- Run a complete Auto-Scan to make sure other modules do not have codes which may indicate the coding is incorrect or incorrect modules are installed in the vehicle. This includes, but is not limited to, addresses 09-Centeral Electronics and 16-Steering Wheel.
'If the remotes will not match and the module is not confirming during the Adaptation process check the following possible causes:
- Incorrect remote(s)
- Incorrect Coding
- Factory Mode enabled in new module
- Incorrect control module
- Old remote control positions aren't cleared. Use the
Les liens ne sont visibles que pour les membres confirmés.procedure as needed.
Donc, c'est bien ce que je pensais, du moment que ton véhicule active les clignotant lors de la procédure d’appairage, c'est que l'émetteur fonctionne correctement et est reconnu par le récepteur...
Et j'en reviens donc à ce que j'ai déjà dit depuis des lustres, à savoir ce qui est expliqué dans le Wiki Ross-Tech :
Remote Control Synchronization
The synchronization is now finished.
- If locked, open the car using the drivers door lock.
- Press the remote control unlock button.
- Put the key in the ignition lock and switch on ignition.
- Switch off ignition and pull the key out of the ignition lock.
- Press the remote control lock or unlock button.
À vrai dire j'ai pas trop envie d'essayer et de faire le bazar sur ma Golf, ça fonctionne nikel, donc j’évite.
Donc j'ai reçu la nouvelle clé (ali express) aujourd’hui et ce soir je suis aller voir si ça fonctionne, après avoir fait un apprentissage de clé sur le Touran, mais ça n'a pas fonctionné... du moins la centralisation à la télécommande ne ferme toujours pas...
[Test][/test]Adaptation
Channel 000: Remote Control Clearing
- This Adaptation Channel is used to clear all matched Remote Controls.
Channel 001: Remote Control Matching
- Start Matching new/additional Remote Controls with entering 1, then Test and Save the New Value.
- Press and hold the Unlock button for at least one second on each Remote Control you want to add, the Blinkers will light up to confirm the Adaptation Process of each Remote Control.
Notes:
[Test]
- The time for matching remotes after saving the new value should not exceed 15 seconds. You can add a maximum of 4 remotes.
- If the [Test][/Test][Test] and/or [Save] buttons are gray and not clickable the module likely has all 4 positions filled and clearing remotes will be necessary in Channel 000.
- Remote Control for Cars equipped with Keyless Entry and Access are automatically being matched when
Les liens ne sont visibles que pour les membres confirmés..
[/test]
[/test]
- Wiki Ross-Tech : «Les liens ne sont visibles que pour les membres confirmés.».
Special Notes
If the remotes will not operate but are confirming while matching during the Adaptation process check the following possible causes:
- Verify the module is not new and still in Factory Mode.
- Check the ignition S-contact switching and driver door latch measuring block switching because remotes will not lock the doors if either are faulty/implausible.
- Run a complete Auto-Scan to make sure other modules do not have codes which may indicate the coding is incorrect or incorrect modules are installed in the vehicle. This includes, but is not limited to, addresses 09-Centeral Electronics and 16-Steering Wheel.
'If the remotes will not match and the module is not confirming during the Adaptation process check the following possible causes:
- Incorrect remote(s)
- Incorrect Coding
- Factory Mode enabled in new module
- Incorrect control module
- Old remote control positions aren't cleared. Use the
Les liens ne sont visibles que pour les membres confirmés.procedure as needed.
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?