OFFSET | [ 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 ] |
7H0937086H | [ A0 B0 79 3A 0E 21 20 12 00 20 08 10 2D 2B 8C D4 00 40 41 0F 60 04 00 00 30 00 00 00 00 00 ] |
*7H0937086H | [ A0 B0 79 3A 0E 21 20 12 00 20 08 10 2D 2B 8C D4 00 C0 41 0F 60 04 00 00 30 00 00 00 00 00 ] |
7H0937089F | [ 22 A0 30 3A 0E 61 24 22 93 28 4E 71 6E EB 8F D5 C2 80 67 0F 60 85 38 41 30 00 00 00 00 00 ] |
Ton codage 042200 n'est pas bon, donc si c'était ton ancien codage, il va falloir trouver celui qui s'adapte sur ton nouveau BCM !!!!
Installation & Wiring
- Install proper Cruise Control Switch/Lever
- Add the Wiring from Cruise Control Switch/Lever to Central Electronics Control Module (J519)
- Add the Wiring from Cruise Control Switch/Lever to Fuse Box/Engine Control Module
Additional Information can be found in the Repair Manuals, the Wiring Diagrams, the Parts Catalog and/or the Instructions included in the Retrofitting Kit.
Configuration
The following Activations are necessary to ensure that the newly fitted parts are properly recognized and are ready to use.
Also see this page for an explanation of CCS activation:
- Update the Engine Control Module (J623 / #01) Coding.
- Make sure that the Engine is NOT running, otherwise the new Coding will be rejected. Models equipped with Start/Stop System do have a Shutoff Switch/Button which will deactivate the Start/Stop Function.
- As a Rule of Thumb, if the Engine Control Module uses a Short Coding the Activation is being done using
Les liens ne sont visibles que pour les membres confirmés.. If the Engine Control Module uses a Long Coding the Activation is done in (Long) Coding itself. Please also note that there are different Coding Variants for Long Coding.- Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be used by the Long Coding Assistant once you access the Function using VCDS.
Les liens ne sont visibles que pour les membres confirmés.
Toi tu es en « short coding » sur le calculateur moteur, donc il te faut utiliser l'option « Coding-II » (il faut suivre le lien du sujet...).
Activating Cruise Control on a new (DBW) ECU using Login
DBW (Drive-by-Wire) Factory fresh ECU's often come with cruise control de-activated.
[Select]
[01 - Engine]
[Login - 11] or if that function is not available then use [Coding - 11] instead
Enter 11463 to activate cruise control
[Do It!]
Sur le lienLes liens ne sont visibles que pour les membres confirmés.(activation du CCS), j'en conclus que je dois suivre ces étapes.
Est-ce que cela vous semble cohérent ?
Notes:
- You may have to cycle the key off and back on before the CCS is activated and the letter "G" is shown in the component field.
- The
Les liens ne sont visibles que pour les membres confirmés.may need to be completed before CCS operates. <- TU FAIS D'ABORD SANS...- Adaptive Cruise Control (ACC) uses the letter A instead of G in the component field.
- If the incorrect Cruise Control type is activated it will be necessary to deactivate it using the Login of 16167 followed by a key cycle and enabling the proper type.
Si le « G » n'apparaît pas tu fais le «Les liens ne sont visibles que pour les membres confirmés.».
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?
We use cookies and similar technologies for the following purposes:
Do you accept cookies and these technologies?